This Resource

 

 

We have discovered the article on Installing A Bathtub down the page on the internet and figured it made sense to share it with you here.

Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently accessible, the task can move immediately; if you have to open up a wall to eliminate the old bathtub as well as position the brand-new tub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to leave the old tub as well as set in the brand-new one. Make sure you have actually qualified on your own for the job as well as fit attempting it. As opposed to employing a service provider to take over a halfway-completed task, it is much better to take into consideration using one before you begin. Opportunities are you may need an expert plumber to make tube links.
This article will aid you mount a new tub in your bathroom if you have already purchased a brand-new bathtub and do not require to alter the plan of your previous water pipes.
Your tools and also material checklist must comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been eliminated, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washers are in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type should be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Setting up the Bathtub

Making use of the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the tub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest flexible tap connector to the proper supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water system as well as examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bath tub as well as also inspect the overflow outlet and the regular outlet for leakages.
Finally, deal with the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the tub needs to wait up until the bath tub has been made use of at least when as this will resolve it into its final placement.

 

 

Preparing for the Installment

Firstly, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final setting.

 

 

Tiling Around the Tub

In the area where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath as well as the tiling, resulting in issues with moisture as well as feasible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can break fairly early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you like reading up on A Step-by-Step Guide to Installing a Bathtub? Make feedback below. We would be delighted to find out your views about this blog entry. Hoping to see you back again later on. Those who liked our blog posting please don't forget to share it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Schedule Now!